[Enhancement Effects and Mechanisms of Microscale Zero Valent Iron on the Performance of Anaerobic Co-digestion of Waste Activated Sludge and Food Waste].

Focusing on low biogas yields in the anaerobic co-digestion of waste activated sludge and food waste, the enhancing effects and mechanisms of microscale zero valent iron (mZVI) on anaerobic co-digestion was investigated. The results indicated that the addition of mZVI enhanced the methanogenesis stage of co-digestion but had no significant effect on the solubilization, hydrolysis, and acidification stages. With a dosage of 10 g·L-1 mZVI, the cumulative methane yield (based on VS) within 15 days reached 238.68 mL·g-1, which was 20.05% higher than the control group. The mechanism analysis showed that mZVI promoted electron transport system (ETS) activity (based on INTF/TS), which increased to 21.50 mg·(g·h)-1 with 10 g·L-1 mZVI compared to 13.43 mg·(g·h)-1 in the control group. Furthermore, mZVI enhanced direct interspecies electron transfer (DIET) between specific bacteria and methanogens. Microbial community analysis demonstrated that the abundance of DIET-related microorganisms, such as Syntrophomonas, Methanosarcina, and Methanobacterium, was higher in presence of mZVI.

Ketoplatin in triple-negative breast cancer cells MDA-MB-231: High efficacy and low toxicity, and positive impact on inflammatory microenvironment.

Triple-negative breast cancer (TNBC) shares the molecular features facilitating epithelial-to-mesenchymal transition (EMT), which contributed to tumor invasion and metastasis. A platinum(IV) conjugate ketoplatin deriving from FDA-approved drugs cisplatin and ketoprofen was designed and prepared to enhance antitumor activity and suppress EMT in TNBC via positive impact on inflammatory microenvironment by modulating COX-2 signal. As a prodrug, ketoplatin afforded 50.26-fold higher cytotoxicity than cisplatin against TNBC mesenchymal-stem cell-like MDA-MB-231 cells, partly attributing to its dramatic increase of cellular uptake and DNA damage. More importantly, EMT progress in MDA-MB-231 was markedly restrained by ketoplatin, resulting from the suppression of vimentin and N-cadherin mediated by down-regulated COX-2. Further in vivo investigation exhibited that ketoplatin effectively inhibited tumor growth and reduced systemic toxicity compared to cisplatin. Overall, ketoplatin possessed high antitumor activity and low toxicity against TNBC MDA-MB-231 in vitro and in vivo.

[Optimization of analysis methods for Astragali Radix and quality evaluation of standard decoction of Astragali Radix].

Astragali Radix is commonly used as bulk medicinal materials. Chinese Pharmacopoeia contains about 150 compound preparations of Astragali Radix, but the sample preparation method under the determination of Astragali Radix content in Chinese Pharmacopoeia is tedious and time-consuming, not convenient for the test of a large number of samples. Therefore, it is of great significance to simplify the sample preparation method and improve the practicability of the method for the quality control of Astragali Radix and its preparations. In this study, ultrasonic extraction method was used instead of heated reflux extraction, and solid phase extraction method was used to enrich and prepare the samples. A set of practical quality evaluation method was established for Astragali Radix slices and standard decoction, greatly shortening the sample preparation time and improving the accuracy of the method. The results of Astragali Radix standard decoction analysis showed that the transfer rate of calycosin 7-O-ß-D-glucospyranoside,(96.5±28.7)%, had great variation, which was found to be related to the conversion of mulberry isoflavone glucoside into calycosin 7-O-ß-D-glucospyranoside during the preparation of standard decoction. The transfer rates were(59.4±14.4)% and(101.3±12.3)% for calycosin and astragaloside Ⅳ respectively, which were relatively stable. Therefore, it is suggested that Astragali Radix slices and water decoction preparations should be evaluated by using calycosin and astragaloside Ⅳ as the quality evaluation index. The results provide a scientific and practical method for quality control of Astragali Radix slices and its standard decoction, and also provide scientific evidence for quality evaluation of the preparations.

Anomalous Mode Transitions in High Power Distributed Bragg Reflector Quantum Cascade Lasers.

In this paper, an anomalous spectral data of distributed Bragg reflector (DBR) quantum cascade lasers (QCLs) emitting around 7.6 µm is presented. The two-section DBR lasers, consisting of a gain section and an unpumped Bragg reflector, display an output power above 0.6 W in continuous wave (CW) mode at room temperature. The anomalous spectral data is defined as a longitudinal mode which moves toward shorter wavelengths with increasing temperature or injection current, which is unexpected. Although the longer wavelength modes are expected to start lasing when raising device temperature or injection current, occasional mode hops to a shorter wavelength are seen. These anomalous mode transitions are explained by means of modal analysis. The thermal-induced change of the refractive index implied by an increase in the temperature or injection current yields nearly periodic transitions between cavity modes.

Demonstration of High-Power and Stable Single-Mode in a Quantum Cascade Laser Using Buried Sampled Grating.

High-power, low-threshold stable single-mode operation buried distributed feedback quantum cascade laser by incorporating sampled grating emitting at λ ~ 4.87 µm is demonstrated. The high continuous wave (CW) output power of 948 mW and 649 mW for a 6-mm and 4-mm cavity length is obtained at 20 °C, respectively, which benefits from the optimized optical field distribution of sampled grating. The single-mode yields of the devices are obviously enhanced by controlling cleaved positions of the two end facets precisely. As a result, stable single-mode emission and mode tuning linearly without any mode hopping of devices are obtained under the different heat sink temperatures or high injection currents.

New NSAID-Pt(IV) prodrugs to suppress metastasis and invasion of tumor cells and enhance anti-tumor effect in vitro and in vivo.

The great interest in epithelial-to-mesenchymal transition (EMT) programme lies in its association with process of metastasis and invasion, which is a crucial cause of cancer-related death. Herein, we designed and reported three new NSAID-Pt(IV) prodrugs, taking Non-Steroid Anti-Inflammatory Drugs (NSAIDs) to disrupt EMT programme and assist genotoxic platinum-based drugs as a cytotoxicity booster, to offer a class of potential anticarcinogens with a multi-functional action mechanism. The NSAID-Pt(IV) prodrugs, especially Eto-Pt(IV), highly enhanced cellular uptake with amount up to 42-fold at 3 h compared with CDDP, and greatly increased DNA damage and cell apoptosis, showing much higher cytotoxicity than cisplatin in the tested cancer cells even in A549/cis cells. Among of them, Eto-Pt(IV) and Car-Pt(IV) exhibited more excellent activity than Sul-Pt(IV), arising from their reduction-labile and favorable lipophilicity. Most strikingly, Eto-Pt(IV) markedly inhibited metastasis and invasion of MCF-7 cells, owing to its COX-2 suppression that down-regulated active MMP-2, vimentin protein and up-regulated E-cadherin. In vivo, Eto-Pt(IV) displayed potent antitumor activity and no observable toxicity in BALB/c nude mice bearing MCF-7 tumors.

Low voltage-defect quantum cascade lasers based on excited-states injection at λ ∼ 8.5 µm.

A quantum cascade laser emitting at λ∼8.5 µm based on the excited-state injection is presented. The operating voltage is reduced for a low-voltage defect in the excited-state design, compared with the conventional ground-state injection design. The threshold voltage and voltage defect are as low as 6.3 V and 54 mV for a 30-stage active region, respectively. Devices were fabricated through standard buried-heterostructure processing to decrease the heat accumulation. A continuous-wave optical power of 340 mW is obtained at 283 K with a threshold current density of 2.7 kA/cm2. Such a design has the potential to further improve the wall plug efficiency for increased voltage efficiency.

Chlorambucil-conjugated platinum(IV) prodrugs to treat triple-negative breast cancer in vitro and in vivo.

Modification of platinum (II) into lipophilic platinum (IV) compounds by introducing biologically active molecules were widely employed to develop new platinum-based prodrugs in the past decade. In this paper, two chlorambucil platinum (IV) complexes, CLB-Pt and CLB-Pt-CLB, were synthesized and displayed very potent antiproliferative activity against all the tested cancer cell lines, such as A549, HeLa and MCF-7, especially to treat the well-known refractory triple-negative breast cancer. CLB-Pt-CLB significantly improved cell-killing effect in triple-negative subtype MDA-MB-231 cells, and showed much stronger cytotoxicity than either monotherapy or combination of cisplatin and chlorambucil. CLB-Pt-CLB prodrug entered cells in dramatically increased amount compared with cisplatin and enhanced DNA damage, inducing cancer cell apoptosis. It exhibited high anticancer activity and no observable toxicity in BALB/c nude mice bearing MDA-MB-231 tumors. The chlorambucil moiety not only greatly assisted the passive diffusion of CLB-Pt-CLB into cells, but also produced the synergism with cisplatin in targeting DNA.

Tapered Quantum Cascade Laser Arrays Integrated with Talbot Cavities.

Power scaling in broad area quantum cascade laser (QCL) usually leads to the deterioration of the beam quality with an emission of multiple lobes far-field pattern. In this letter, we demonstrate a tapered QCL array integrated with Talbot cavity at one side of the array. Fundamental supermode operation is achieved in the arrays with taper straight-end connected to the Talbot cavity. Lateral far-field of the fundamental supermode shows a near diffraction limited beam divergence of 2.7°. The output power of a five-element array is about three times as high as a single-ridge laser with an emission wavelength of around 4.8 µm. However, arrays with the taper-end connected to the Talbot cavity always show a high-order supermode operation whatever Talbot cavity length is.

Stable Single-Mode Operation of Distributed Feedback Quantum Cascade Laser by Optimized Reflectivity Facet Coatings.

In this work, quantum cascade lasers (QCLs) based on strain compensation combined with two-phonon resonance design are presented. Distributed feedback (DFB) laser emitting at ~ 4.76 µm was fabricated through a standard buried first-order grating and buried heterostructure (BH) processing. Stable single-mode emission is achieved under all injection currents and temperature conditions without any mode hop by the optimized antireflection (AR) coating on the front facet. The AR coating consists of a double layer dielectric of Al2O3 and Ge. For a 2-mm laser cavity, the maximum output power of the AR-coated DFB-QCL was more than 170 mW at 20 °C with a high wall-plug efficiency (WPE) of 4.7% in a continuous-wave (CW) mode.

Room temperature continuous wave quantum dot cascade laser emitting at 7.2 µm.

We demonstrate a quantum cascade laser with active regions consisting of InAs quantum dots deposited on GaAs buffer layers that are embedded in InGaAs wells confined by InAlAs barriers. Continuous wave room temperature lasing at the wavelength of 7.2 µm has been demonstrated with the threshold current density as low as 1.89 kA/cm2, while in pulsed operational mode lasing at temperatures as high as 110 °C had been observed. A phenomenological theory explaining the improved performance due to weak localization of states had been formulated.

High Efficiency, Low Power-Consumption DFB Quantum Cascade Lasers Without Lateral Regrowth.

Very low power-consumption distributed feedback (DFB) quantum cascade lasers (QCLs) at the wavelength around 4.9 µm were fabricated by conventional process without lateral regrowth of InP:Fe or using sidewall grating. Benefitted from the optimized materials and low waveguide loss, very low threshold current density of 0.5 kA/cm2 was obtained for a device with cavity length of 2 mm. Combined with the partial-high-reflection coating, the 1-mm-long DFB QCL achieved low power-consumption continuous wave (CW) operation up to 105 °C. The CW threshold power-consumptions were 0.72 and 0.78 W at 15 and 25 °C, respectively. The maximum CW output power was over 110 mW at 15 °C and still more than 35 mW at 105 °C. At 15 °C, wall-plug efficiency of 5.5% and slope efficiency of 1.8 W/A were deduced, which were very high for low power-consumption DFB QCLs.

[Optimization Study on the Nitrogen and Phosphorus Removal of Modified Two- sludge System Under the Condition of Low Carbon Source].

This paper explored the method of resolving insufficient carbon source in urban sewage by comparing and analyzing denitrification and phosphorus removal (NPR) effect between modified two-sludge system and traditional anaerobic-aerobic-anoxic process under the condition of low carbon source wastewater. The modified two-sludge system was the experimental reactor, which was optimized by adding two stages of micro-aeration (aeration rate 0.5 L · mm⁻¹) in the anoxic period of the original two-sludge system, and multi-stage anaerobic-aerobic-anoxic SBR was the control reactor. When the influent COD, ammonia nitrogen, SOP concentration were respectively 200, 35, 10 mg · L⁻¹, the NPR effect of the experimental reactor was hetter than that of thecontrol reactor with the removal efficiency of TN being 94.8% vs 60.9%, and TP removal being 96.5% vs 75%, respectively. The effluent SOP, ammonia, TN concentration of the experimental reactor were 0.35, 0.50, 1.82 mg · L⁻¹, respectively, which could fully meet the first class of A standard of the Pollutants Emission Standard of Urban Wastewater Treatment Firm (GB 18918-2002). Using the optimized treatment process, the largest amounts of nitrogen and phosphorus removal per unit carbon source (as COD) were 0.17 g · g⁻¹ and 0.048 g · g⁻¹ respectively, which could furthest solve the lower carbon concentration in current municipal wastewater.

Enhancement of post-anoxic denitrification for biological nutrient removal: effect of different carbon sources.

Previous research has demonstrated that post-anoxic denitrification and biological nutrient removal could be achieved in the oxic/anoxic/extended-idle wastewater treatment regime. This study further investigated the effect of different carbon sources on post-anoxic denitrification and biological nutrient removal. Acetate, propionate (volatile fatty acids (VFAs)), glucose (carbohydrate), methanol, and ethanol (alcohol) were used as the sole carbon source, respectively. The experimental results showed that VFA substrates led to an improvement in nitrogen and phosphorus removal. The total nitrogen and phosphorus removal efficiency values driven by acetate achieved 93 and 99%, respectively. In contrast, glucose present in mixed liquor deteriorated total nitrogen and phosphorus removal efficiency values to 72 and 54%. In the reactors cultured with methanol and ethanol, 66 and 63% of the total nitrogen were removed, and phosphorus removal efficiency values were 78 and 71%, respectively. The mechanism studies revealed that different carbon sources affected the transformations of intracellular polyhydroxyalkanoates (PHAs) and glycogen. PHAs are the dominant storages for microorganisms cultured with VFA substrates. Though glycogen is not the favorable energy and carbon source for polyphosphate-accumulating organisms, it can be consumed by microorganisms related to biological nitrogen removal and is able to serve as the electron donor for post-anoxic denitrification.

Effects of Cd(II) on wastewater biological nitrogen and phosphorus removal.

Short-term and long-term effects of Cd(II) on wastewater biological nitrogen and phosphorus removal were investigated with respect to microorganism abundances, enzyme activities, and polyhydroxyalkanoates (PHAs) and glycogen transformations. Though no obvious effects on wastewater biological nutrient removal were observed after short-term exposure, the long-term exposure of 10 mg L(-)(1) Cd(II) inhibited nitrification and phosphorus uptake. Compared with the absence of Cd(II), the presence of 10 mg L(-1) of Cd(II) decreased total nitrogen and phosphorus removal efficiencies from 97% and 98% to 88% and 18%, respectively. Mechanism studies revealed that Cd(II) affected the transformations of intracellular PHAs and glycogen, and the activities of oxidoreductase and polyphosphate kinase, resulted in the decrease of nitrite oxidizing bacteria and polyphosphate accumulating organisms abundance, which might be the major reason for the negative effects of long-term exposure to 10 mg L(-1) Cd(II) on biological nitrogen and phosphorus removal.

Temperature influence on biological phosphorus removal induced by aerobic/extended-idle regime.

Previous researches have demonstrated that biological phosphorus removal (BPR) from wastewater could be driven by the aerobic/extended-idle (A/EI) regime. This study further investigated temperature effects on phosphorus removal performance in six A/EI sequencing batch reactors (SBRs) operated at temperatures ranging from 5 to 30 °C. The results showed that phosphorus removal efficiency increased with temperature increasing from 5 to 20 °C but slightly decreased when temperature continually increased to 30 °C. The highest phosphorus removal rate of 97.1 % was obtained at 20 °C. The biomass cultured at 20 °C contained more polyphosphate accumulating organisms (PAO) and less glycogen accumulating organisms (GAO) than that cultured at any other temperatures investigated. The mechanism studies revealed that temperature affected the transformations of glycogen and polyhydroxyalkanoates, and the activities of exopolyphosphatase and polyphosphate kinase activities. In addition, phosphorus removal performances of the A/EI and traditional anaerobic/oxic (A/O) SBRs were compared at 5 and 20 °C, respectively. The results showed the A/EI regime drove better phosphorus removal than the A/O regime at both 5 and 20 °C, and more PAO and less GAO abundances in the biomass might be the principal reason for the higher BPR in the A/EI SBRs as compared with the A/O SBRs.

Biological nutrient removal in a sequencing batch reactor operated as oxic/anoxic/extended-idle regime.

Previous researches have demonstrated that biological phosphorus removal from wastewater could be induced by oxic/extended-idle (O/EI) regime. In this study, an anoxic period was introduced after the aeration to realize biological nutrient removal. High nitrite accumulation ratio and polyhydroxyalkanoates biosynthesis were obtained in the aeration and biological nutrient removal could be well achieved in oxic/anoxic/extended-idle (O/A/EI) regime for the wastewater used. In addition, nitrogen and phosphorus removal performance in O/A/EI regime was compared with that in conventional anaerobic/anoxic/aerobic (A(2)/O) and O/EI processes. The results showed that O/A/EI regime exhibited higher nitrogen and phosphorus removal than A(2)/O and O/EI processes. More ammonium oxidizing bacteria and polyphosphate accumulating organisms and less glycogen accumulating organisms containing in the biomass might be the principal reason for the better nitrogen and phosphorus removal in O/A/EI regime. Furthermore, biological nutrient removal with O/A/EI regime was demonstrated with municipal wastewater. The average TN, SOP and COD removal efficiencies were 93%, 95% and 87%, respectively.

Microbial community analysis involved in the aerobic/extended-idle process performing biological phosphorus removal.

Recently, it has been found that biological phosphorus removal can be achieved in an aerobic/extended-idle (AEI) process using both glucose and acetate as the sole substrate. However, the microbial consortiums involved in glucose-fed and acetate-fed systems have not yet been characterized. Thus the aims of this paper were to investigate the diversities and dynamics of bacterial communities during the acclimation period, and to quantify polyphosphate-accumulating organisms (PAOs) and glycogen-accumulating organisms (GAOs) in the systems. The phylogenetic analysis showed that the microbial communities were mainly composed of phylum Proteobacteria, Bacteroidetes, Chlorobi and another six kinds of unclassified bacteria. Fluorescence in-situ hybridization (FISH) analysis revealed that PAOs and GAOs accounted for 43 ± 7 and 16 ± 3% of all bacteria in the glucose-fed system, and 19 ± 4 and 35 ± 5% of total bacteria in the acetate-fed system, respectively. The results showed that the conventional PAOs could thrive in the AEI process, and a defined anaerobic zone was not necessarily required for putative PAOs growth.

Intersubband absorption properties of high Al content AlxGa1-xN/GaN multiple quantum wells grown with different interlayers by metal organic chemical vapor deposition.

High Al content AlxGa1-xN/GaN multiple quantum well (MQW) films with different interlayers were grown by metal organic chemical vapor deposition. These MQWs were designed to achieve intersubband (ISB) absorption in the mid-infrared spectral range. We have considered two growth conditions, with AlGaN interlayer and GaN/AlN superlattice (SL) interlayer, both deposited on GaN-on-sapphire templates. Atomic force microscopy images show a relatively rough surface with atomic-step terraces and surface depression, mainly dominated by dislocations. High-resolution X-ray diffraction and transmission electron microscopy analyses indicate that good crystalline quality of the AlGaN/GaN MQW layer could be achieved when the AlGaN interlayer is inserted. The ISB absorption with a peak at 3.7 µm was demonstrated in MQW films with AlGaN interlayer. However, we have not observed the infrared absorption in MQW films with GaN/AlN SL interlayer. It is believed that the high dislocation density and weaker polarization that resulted from the rough interface are determinant factors of vanished ISB absorption for MQW films with the GaN/AlN SL interlayer.

Manganese-electrolysed slag treatment: bioleaching of manganese by Fusarium sp.

A fungi strain named Fusarium sp. was isolated from manganese-electrolysed slag by using a gradient dilution spread plate method, identified by 26S RNA sequence analysis and phylogenetic tree analysis, and explored for the bioleaching capacity to manganese (II) from manganese-electrolysed slag in liquid mineral medium under different environmental conditions, including system temperature, incubator rotation speed and initial pH value. DNA sequence and phylogenetic analysis indicated the name of this fungi strain, that is, Fusarium sp., and higher bioleaching efficiencies (71.6%) of manganese by this fungi were observed when the bioleaching was carried out under the optimized conditions as follows: contact time: 72 h; system temperature: 28 degrees C; inoculums concentration: 2% (v/v); incubator rotation speed: 150 rpm; pH 4.0. Because of its low cost, environment friendliness and better efficiency, the bioleaching technique will have a significant impact on manganese-electrolysed slag pollution mitigation.